Best Ways To Make Hand Embroidered Patches

Patches are a fashionable way to dress up a denim,gucci,Puma,Calvin Klein jacket or purses. Embroidered patches are simple to produce at home. You may make any embroidered patch pattern you like and customise it to your liking.

This Article will let you know how to make and apply your homemade patches using four different ways. Choose patterns for each of them based on the size of the patches you wish to make. Although there is no rule, smaller designs, such as the components of a fruit pattern, work nicely. While there are four different ways to make patches, you’ll find that some of them may be mixed and matched. You may construct a felt patch with glue or a pin with varied edge stitching, for example. Experiment with these four methods for manufacturing DIY patches.

Patches that can be ironed on

Iron-on patches are quick and simple to apply, which is always beneficial. Furthermore, these patches may be given as gifts. Simply offer directions for ironing on some easy designs.

Choose a design and trace it onto the cloth using the transfer method that works best for you (the patch in this tutorial was stitched on linen).

Stitch along the boundaries of the pattern, allowing space around the edges. Cut a second piece of fabric, as well as two pieces of paper-backed fusible web, to a comparable size. Iron one piece of fusible web on the cloth that isn’t embroidered. Follow the manufacturer’s directions and make sure your iron is set on the paper side. You’ll need a design, two pieces of fabric, and two pieces of paper-backed fusible web to make iron-on patches.

Fuse Fabric to the Embroidered Piece using Iron-On Patches

Remove the paper from the fusible web and lay the fabric on the back of the embroidered fabric, web side down. To fuse the layers together, iron the non-embroidered component. This adds solidity to your patch and helps keep the edges from fraying. Remove the paper and iron the second piece of fusible web to the plain back of your fused patch.

Cut and Finish Patches Using Iron-On Patches

Following the lines of the pattern and leaving some room around the embroidery, cut around the embroidered shape.

The fusible web helps fabric avoid fraying, but you may also add further fraying protection by stitching a line of running stitch at the edge. Use whip stitch around the edge of your patch to make it seem more like a commercially created patch, as seen in the pin patch instruction below. If you’re connecting this to a frequently cleaned garment, you might want to wait till after it’s ironed in place to add the line of stitching for further security.

Sew-on Felt Patches Instructions

Hold your iron-on patch in place and iron it from the back of the object you’re attaching it to when you’re ready to use it. To get through the layers, make sure your iron is set to a high enough heat setting.

Mark the design with a water-soluble stabiliser or tracing paper to embroider on felt. Make sure the embroidery is arranged so that there is enough room around the pattern to trim the patch.

Embroider the design in whatever way you like. On little patches, satin stitching looks excellent, but you may also stick to all outlines.

Remove the marks after the needlework is completed. Carefully take away the tracing paper if you utilised that approach. Soak the final stitching in the water-soluble stabiliser technique, and after the material dissolves, lay the felt flat to dry.

It’s critical to soak the needlework in cool or room temperature water if you’re using wool or wool mix felt (which holds up the best). Your patch will shrink if you wash it in hot water.

Cutting Felt Sew-On Patches

Cut around the needlework to complete the patch. You may either cut out a standard form, such as a circle or hexagon, or loosely follow the stitching’s shape as shown.

There’s approximately 1/4 inch of felt visible on the example, so there’s plenty of room to sew the patch onto something. However, you can go a lot closer. Make cautious not to clip the stitches or trim the felt too near to the point where the stitches come out.

Finishing and Attaching Felt Sew-On Patches

Pin or hold the felt patch in place where you want it to go to attach it. Using ordinary embroidery floss, stitch around the edge. As with appliqué, you can use blanket stitch or whip stitch.

Felt patches should not be cleaned on a regular basis. Use the gentle cycle or store the mended item in a delicates bag or pillowcase if they do need to go through the laundry.

Patches with Self-Adhesive Backing

Do you want a permanent patch that you can place on your clothes like a sticker? This is the approach you should take.

You’ll need the fabric you’re sewing on, a piece of thick stabiliser, and permanent peel-and-stick fabric adhesvie to construct self-adhesive patches.

Self-Adhesive Patches Instructions

Transfer your design to any cloth you want to sew on. The pattern should be placed on the bias of the cloth to avoid fraying later.

As you set the fabric in your stitching hoop, cut a piece of stiff, hefty stabiliser and layer it below it. Stitch through both levels of the design. Because getting through the stabiliser might be difficult, use a powerful needle.

Cutting and Finishing Edges on Self-Adhesive Patches

Trim the embroidered form around it, allowing a little room for sewing the edges. Cutting more geometric forms is better for this type of patchmaking.

Get more updates : Ribbon embroidery